Announcement

Collapse
No announcement yet.

Project Binky

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Project Binky

    Decidedly cool














    Episode 15


    Episode 16


    outtakes part 4


    Episode 17


    Episode 18



    Episode 19


    Episode 20


    Intermediate episode starting Howie


    Howie part deux


    Episode 21


    Episode 22

    Episode 23


    what's next


    Episode 24


    Episode 25


    Episode 26


    Enhancement


    Episode 27


    Episode 28


    Episode 29

    Episode 30


    Outtakes 5


    Episode 31


    another Howie


    Episode 32


    Episode 33


    Episode 34


    Episode 35


    Episode 36


    Episode 37
    Last edited by SuperBuickGuy; December 18, 2021, 01:53 PM.
    Doing it all wrong since 1966

  • #2
    and yes, I just wasted the rest of your afternoon.
    Doing it all wrong since 1966

    Comment


    • #3
      I made a beeline to the fourth video down.

      a lot of work there.
      some interesting things was the driveshaft with center carrier fitting first try.. ricers flex, so they will look exact anyway, even off by 10mm.
      the bell the front yoke slides into will sound like a triangle (music instrument).

      the plug welds laminate.. that is two thumbs up. A subaru awd rocker needs that in 5 foot 4 inch runs...

      on the sheetwrok following, that is amazing and patient.
      something I notice no body welder has mentioned yet, that I have noticed..
      the seam welds or places concerned with heat and buckling. Little dots first, fill in as you go..

      a strong ground takes care of most of it. I find steel car ramps, and a jack up to the bottom of my stainless rockers sets the pace for anywhere on the car. (I made every mistake to finally realize it was the earth ground nowhere near strong enough)

      the switch is connected to a wire that goes to a control box which takes power from a battery to turn a motor that winds a screw which pulls an arm which is attached to a shaft that has a bracket that is bolted to the jig.
      a rochestor monojet in action.

      2stroketurbo on you tube is doing something even crazier with a subaru 360..and it will look like stock.
      similar ricer engine numbering, except a mistibusuhuushi something.
      Last edited by Barry Donovan; June 16, 2014, 10:17 PM.
      Previously boxer3main
      the death rate and fairy tales cannot kill the nature left behind.

      Comment


      • #4
        Loving that portable grinder stand/holder.....lots of cool stuff going on here!
        Of all the paths you take in life - make sure a few of them are dirt.

        Comment


        • #5
          To hell with amazon prime and netflix - I have a new favorite channel. These blokes are funny.
          There's always something new to learn.

          Comment


          • #6
            damn, that dudes talented...and handy with a grinder....
            If you can leave two black stripes from the exit of one corner to the braking zone of the next, you have enough horsepower. - Mark Donohue

            Comment


            • #7
              I love stuff like this! It also makes you realize if you can imagine it, you can build it.
              Just groovin' to my own tune.

              Comment


              • #8
                Episode 7
                Doing it all wrong since 1966

                Comment


                • #9
                  that door lock has to be the coolest and ridiculously complicated thing ever.
                  Hellinor- 2005 Mustang GT-Bolt ons, in need of a turbo

                  War Wagon- 1966 Bel Air Wagon-355 Crate motor, 700r4, flies pretty good for a brick...

                  Comment


                  • #10
                    i have been stalking there youtube page for this episode.
                    Neal

                    Drag Week 2010, 2011, 2012, 2013

                    Comment


                    • #11
                      Episode 8
                      Doing it all wrong since 1966

                      Comment


                      • #12
                        Great design, excellent execution. Just like my stuff only competent.

                        Dan

                        Comment


                        • #13
                          I forgot about this...I love it....
                          If you can leave two black stripes from the exit of one corner to the braking zone of the next, you have enough horsepower. - Mark Donohue

                          Comment


                          • #14
                            So, cool that episode 8 came out so quickly after blowing through the first 7 episodes . If I could only more of this type of fabricating videos I could pitch my sattilite t.v.
                            Previously HoosierL98GTA

                            Comment


                            • #15
                              Geez, so many of you are raving about this series, I can only presume it got much better in later episodes. After wasting 18-minutes of my life on the first one, I was like ... Meh !!!

                              Comment

                              Working...
                              X