I had gotten a radiator off of eBay, and I had this parking brake left over from the CJ5. The radiator needed the ears extended out to be as wide as the fenderwells and I'll have to figure out how or where to get a parking brake cable from which will mate the Jeep/FBody parking brake pedal to the orignal crossbar for the EBrake in the rear.
Announcement
Collapse
No announcement yet.
The Blue Truck
Collapse
X
-
Well, remember I said earlier that the arc welding was scary but not cracking?
Guess where it decided to crack... I can think of several reasons why it could or would, but I decided to simply stop-drill, dig out the cracks with the cutoff wheel, and the weld 'em up to keep an eye on them.
This did have an amazing amount of arc weld slag pile laying on top of it I ground off - so I expect it was cracked before the grafting, but who knows.Livin the dream
Comment
-
I've POR-15'd the floors, "patched" the extra holes in the firewall with aluminum slugs and dum-dum, and am in the process of coating the interior with FatMat. The product goes on very easily and it sure likes the heat gun, especially in this year's chilly temps.
I hope that the aluminum slugs will help the FatMat not get punctured.... We'll see.Livin the dream
Comment
-
So this means ShopDog is calling me out there and I have to go out and continue the FatMat and get the 305 on an engine stand so I can flip it and change the oil pan. yea, the oil pan has a hole in it that is patched with Epoxy. Not JBWeld, but old-fashioned household mostly clear Epoxy.Livin the dream
Comment
-
Originally posted by DanStokes View PostComing along nicely.
On the brake deal - on my S-10 clutch master I made similar though smaller reinforcing plates then I found that I had the stock S-10 clutch master reinforcing rods that go from the steering column bracket to the firewall. I think there's a pic in my build thread. Anyhow, something like that might be a good thing for you if you want it even stiffer.
Dan
There is still some welding to do under the dash and I was planning on triangulating the pedal assembly up to the dash support it with some 1/4" round tube and 11ga plate before I was done. The mount on the brake pedal assembly to the bottom of the dashboard has also been graced with a torch, so even though I am somewhat happy with the firewall mount, the inside mount for the pedal assembly still ain't right.Livin the dream
Comment
-
Originally posted by JOES66FURY View Postwow, project creep huh? awesome.
Plus, it's still a quick a spray-can rebuild. Interior was 1.5 cans of mix and so far it has one can of 2K gloss clear.
I ain't spending more than I have to on this one. Scrape the bondo off of the outside and shoot it with a spray can.
So Scope Creep? Not really :D I took the first picture inside on 12/19! I think Squirrel has inspired me!Livin the dream
Comment
-
Really loving this build! What's the rear axle like? Staying rear drum I'd assume? Hopefully something 3.42ish with a factory posi?
You've chosen one of my all time favorite colors - I don't care if it came from a spray can! This is going to be a heck of a nice truck!
Well done!There's always something new to learn.
Comment
-
Thanks Milner!
I haven't put a wrench on the rear yet, but it's a 10-bolt, open, and I suspect 3:08, which most likely came from the some '68 Chevelle that gave up the crossmember. I was planning on opening that can of worms later this week!
It will stay drums all around, yes - 2 3/4" shoes in the front, 2" in the rear. This ole girl ran fine before and she'll do fineLivin the dream
Comment
-
Sweet - dual master for four wheel drum - which resevior feeds which end of the truck? Which prop valve?
Drums have an inherent advantage - they're lower rolling resistance than discs. It's a truck - it will have plenty of brakes, discs up front can be a down the road upgrade.
Man - you're pushing me closer to getting an older ride to daily drive and just undercoat the whee out of it to fend off the tin worm.
I am continually shocked at the price of insurance for newer vehicles.... legalized extortion.There's always something new to learn.
Comment
-
Wow. Build a quick runner/driver and full restoration look a lot alike. Great job.
The before brake mounting is just terrorifying. I am sure the jumbo Caddy brake pedal made things worse.Last edited by Scott Liggett; February 19, 2014, 09:51 PM.BS'er formally known as Rebeldryver
Resident Instigator
sigpic
Comment
Comment