So yeah, then there is this. How did that get set negative???
Announcement
Collapse
No announcement yet.
1973 F-250 - Turbo BBF - It's off to a new home!
Collapse
X
Collapse
-
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
-
I feex!
I ran the fuel pressure gauge up to the windshield wiper and watched as fuel pressure dropped like a rock under boost.
I started by checking the basics. I just filled the tank was full so it was not that. I pulled the fuel filter and bingo. The filter was completely clogged with fuel cell foam remnants.
I cleaned it out and whoo hoo!! Now it is stupid rich under boost!! Now I need to back up to an earlier tune and start over.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Holy smokes it works!!!
Uploaded an old tune and took it out after work around the parking lot and it didn't lean out!! AFR was around 11.0-11.5 at WOT.
Still only at 5 psi right now, but man this thing feels and sounds rad!!Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Originally posted by Beagle View Postmy city guy wanted to know if my truck was operational, said a video would do. I sent him this one. HAHAHAHAHAHA!!!
That's great James, Goodyear is gonna love it.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Originally posted by BBR View PostThe focus the last few days had been on getting the brake lines sorted and fixed. To recap, this thing has always been hard to bleed and the pedal was always lower than I thought it ahould be. I discovered that somewhere along the way, some previous owner plumbed the master cylinder backwards. On a Ford, the large side of the master cylinder (closest to the booster) should be routed to the front disc brakes and the smaller side is for the rear drums.
The combination valve that these things have is a known problem maker, I decided to use one like the one in my Mustang. It has never given a lick of trouble and performs just as expected. JWS4621 let me rob the one from his parts car.
Of course this meant having to change some of the brake fittings to the proper size. While doing so, I noticed the line I just setup for the rear brakes was still loose when the fitting was as tight as possible in the mc. I pulled it back off and sure enough, the PO only used a single flare. I cut it off and reflared (double) the line, problem solved.
Good news is that I only flared 1 line without first putting the fitting on. Haha
Boring stuff, but completely necessary.
Follow up. I am happy to report the brakes feel awesome now.Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
- Likes 1
Comment
-
I finally put a filter on it. A really big one. I was super worried a rock was going to get flipped by the front tire, bounce around and get eaten by the turbo.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Every truck needs a receiver hitch. We had this hitch on the truck back when it was still a big truck. It hung down under the rear step bumper and looked dumb once we took the rear bumper off. I cut the welds and flipped the center tube over so the receiver is on top of the tube, up out of harm's way. Should be fine for anything this truck will need to pull.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Started to bolt it on and came to the realization that I hated how it fit. Too low and sticky outy. Back to the drawing board.Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Chopped the receiver tube off and the ends off the brackets. I added a couple of pieces of roll cage tubing and now have the beginning of a much more compact receiver hitch. There will be a center bracket tying it to the frame crossmember that is behind it. It won't be as heavy duty as the other one, but it doesn't need to be.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
More hitch work. Welded up the tubes and added an angle support to the center. The center support will attach to the back of the angle.
It looks high, but the top of the ball is really only 1" higher off the floor than the ball on the red Mustang.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Hitch is done. My 1/2" drill destroyed 2 bits and a step bit drilling the frame holes. (Not to mention my hands)
Anyway, it fits as expected, looks decent and it is super solid. There are nine 1/2" bolts holding it to the truck so I figger it will be ok.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
With the GT500 no longer in my garage (Jake has it with him at his summer assignment in Mississippi) I decided to take the truck home. I made it almost home when it died at an intersection. Boo. Starter wouldn't spin it over. Rolled it out of the way sort of and waited for Jonathan (JWS4621) to come rescue me. Haha. The tow of shame. Got the truck home and waited for it to cool off but it still wouldn't turn over. Hooked up the jumper cables, waited a bit and it still wouldn't turn over. Monkeyed with the cables a bit, still nothing. Moved the neg cable from the battery post to a bolt on the accessory drive and zing it spun over and lit right off. Parked it in the garage and then moved the cable to the other bolt. Fired right up with ease. I took a closer look at the block where the cable was attached. Yep. Completely painted. Such a rookie mistake. Doh.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
Comment
-
Washed the shop dust off.
Life is short. Be a do'er and not a shoulda done'er.
1969 Galaxie 500 https://bangshift.com/forum/forum/ba...ild-it-s-alive
1998 Mustang GT https://bangshift.com/forum/forum/ba...60-and-a-turbo
1983 Mustang GT 545/552/302/Turbo302/552 http://www.bangshift.com/forum/forum...485-bbr-s-83gt
1973 F-250 BBF Turbo Truck http://www.bangshift.com/forum/forum...uck-conversion
1986 Ford Ranger EFI 545/C6 https://bangshift.com/forum/forum/ba...tooth-and-nail
- Likes 1
Comment
Comment