Re: Can you identify these cylinder heads????
A smart man would turbo it, then the cage limits how fast you can go, and it falls off the trailer fast, not really worrying about hooking up the smack.
Announcement
Collapse
No announcement yet.
Can you identify these cylinder heads????
Collapse
X
-
Re: Can you identify these cylinder heads????
The car STILL could get a couple 88s on it before Drag Week... I was gonna bring something completely different, but don't know that time permits to come up with a whole nother vehicle.. I am going to the PRI show and I should have a better idea after that as to what kinda setup I will have for Drag Week.. Whatever it is, I should have more power then the Duster can handle.. ;D I have a new HP Performance aluminum block coming that has some "special" deck heights being made just for me. ;) I'm not sure if its getting a tunnel ram w/ a ton of spray OR twin turbos and FI... Time will tell.
Leave a comment:
-
Re: Can you identify these cylinder heads????
Originally posted by Eric68Uh . . . why quad? Wouldn't one big honkin turbo or at most a pair be sufficient for a couple thousand HP?
Leave a comment:
-
Re: Can you identify these cylinder heads????
Uh . . . why quad? Wouldn't one big honkin turbo or at most a pair be sufficient for a couple thousand HP?
Leave a comment:
-
Re: Can you identify these cylinder heads????
I would shit can that whole nitrous/carb crap, and set up an E-85 F.I. quad turbo!!!
BUT!, That purple car would fall apart, running in the 6s. ;D
Leave a comment:
-
Re: Can you identify these cylinder heads????
That would make a good spray head lots of room. :o Good luck ,,,,,,, now how can I get that much air in my weeenie motor ;)
Leave a comment:
-
Re: Can you identify these cylinder heads????
Originally posted by JeffMcKCPerformance Products "Predator" performance cylinder head.
The intake looks like its got wayyyy to small of plenum for the cubes that crosscection of head needs and when filled with the gas from a plate over the top of that fogger it needs even more room, at the top, and more taper. I don't know if a single will work, that looks like a copied SB2 spider on steroids, get a sheet metal intake Eddie
They got the heads right, but the intake was an afterthought.. The new Predator CNC head thats debuting at the PRI show flows over 520cfm and I am told more is left.
Leave a comment:
-
Re: Can you identify these cylinder heads????
Originally posted by JeffMcKCPerformance Products "Predator" performance cylinder head.
The intake looks like its got wayyyy to small of plenum for the cubes that crosscection of head needs and when filled with the gas from a plate over the top of that fogger it needs even more room, at the top, and more taper. I don't know if a single will work, that looks like a copied SB2 spider on steroids, get a sheet metal intake Eddie
Leave a comment:
-
Re: Can you identify these cylinder heads????
Performance Products "Predator" performance cylinder head.
The intake looks like its got wayyyy to small of plenum for the cubes that crosscection of head needs and when filled with the gas from a plate over the top of that fogger it needs even more room, at the top, and more taper. I don't know if a single will work, that looks like a copied SB2 spider on steroids, get a sheet metal intake Eddie
Leave a comment:
-
Re: Can you identify these cylinder heads????
Those are a set of experimental Pontiac tunnel-port heads, originally designed for a special version SD-428 for the Trans Am racing series but reportedly abandoned due to...
[crickets chirping]...
no takers eh?
Leave a comment:
-
Re: Can you identify these cylinder heads????
I know what they are!!!!!....but I ain't tellin', but I will say this, I have seen them go down the track! ;D
Leave a comment:
-
Re: Can you identify these cylinder heads????
and there probably the ones on his car
Leave a comment:
-
Re: Can you identify these cylinder heads????
Originally posted by fabricatordavehow about these http://predatorheads.com/head-features.htm
;)
Leave a comment:
-
Re: Can you identify these cylinder heads????
how about these http://predatorheads.com/head-features.htm
Leave a comment:
-
Re: Can you identify these cylinder heads????
Originally posted by cudadonJudging by the condition of that manifold, it's definately a junkyard or ebay piece! Good thing you know how to weld.
By the way, I've got some spacers and stuff I want to try on my 451, when is the dyno FREE?! Thanks for steering me here! Don
Leave a comment:
Leave a comment: