Announcement
Collapse
No announcement yet.
Search Result
Collapse
29 results.
Keywords
Members
Tags
-
My Dad has a set of 12:1 pop ups for a 283 that I've been tempted to buy from him, but that doesn't seem like a logical choice for a daily( which may...Last edited by leleva; April 3, 2020, 12:58 PM.
- Likes 2
-
Here's an article to help give some ideas.
http://www.hotrod.com/articles/ccrp-...ford-maverick/...
Leave a comment:
-
I'll just trim the exhaust back, till I can't hear the chain rattle. I'll see what the aftermarket supplies for V8 conversion motor mounts, I know they...
Leave a comment:
-
I've ended up acquiring so much 6 cylinder stuff since starting the endeavor, all for nothing now. Maybe I'll have to buy another car to use this stuff...
Leave a comment:
-
Not sure to tell you the truth, I can tell you that solder doesn't stick to carburetors.
Leave a comment:
-
Well in a turn of event, the plan to build a six cylinder for this car has been put on indefinite hold. The 6 cylinder I was going to build would require...Last edited by leleva; October 14, 2017, 08:31 PM.
Leave a comment:
-
They should be press fit into the upper air horn portion. I've had them fall out into the carb, but they've always tapped back in. Gas is pretty hard...
Leave a comment:
-
I usually have to have some one come with me when I go to look at a project because my blinders go up, and all's I see is potential. With that said, this...Last edited by leleva; August 15, 2017, 01:04 AM.
Leave a comment:
-
Not sure what year your camaro is, but I went and looked at the wiring schematics for an 85 and If I read it right there is a relay for the High side...
Leave a comment:
-
I ended up getting laid of in march due to my plant closing, however I had already spent a lot of my tax refund on model A parts so I had some free time...
- Likes 1
Leave a comment:
-
I wouldn't say it's my generation thats causing the car culture to peak, I wouldn't even say it's peaking. A lot of the prices on older cars has been...
Leave a comment:
-
I was stoked to see it on the front page, my dad showed ti to some of the guy's he works with.Like I said the PPG guy mixed it from mixing codes based...Last edited by leleva; April 27, 2017, 12:10 PM.
Leave a comment:
-
Last year ( febuary of 2016) I bought new fenders, then had to wait to save up for paint. Went to the PPG shop in the next town over and they tried to...Last edited by leleva; April 23, 2017, 09:35 AM.
Leave a comment:
-
As long as you have the dual bolt pattern for the starter bolt up. I made this mistake when I swapped the 305 ( Which had the153 tooth flex plate and...Last edited by leleva; February 7, 2017, 05:22 PM.
Leave a comment:
-
I'm going to second what squirrel says about it being a 37-39 truck, my 41's frame is close but a bit different, and my front spring shock mounts extend...
Leave a comment:
-
It will fit as it's only an 1 3/4" taller, if a person runs a low profile air cleaner. There are a few other thing's I've read that cause issues....Last edited by leleva; August 15, 2016, 06:25 PM.
Leave a comment:
-
How did you come about using that go kart slick as the upper wheel?
Leave a comment:
-
As far as the engine I bought a 250 a while back, tore it down, and found it well used, being 60 over with a slight ring ridge, I've been debating If...
Leave a comment:
-
Bent the block? thats crazy. A lot of people have told me to just drop a small block in, and put a shifter on the floor.
Leave a comment:
-
One tip, if you haven't drain the gas that has been sitting in the tank since it was parked, defiantly do so. Also blowing out the lines and replacing...
Leave a comment:
Leave a comment: