Announcement
Collapse
No announcement yet.
Search Result
Collapse
42 results.
Keywords
Members
Tags
-
While scouring the vast depths of the internet, I stumbled upon a gem that I believe deserves to be a permanent fixture in the realm of drum brake enthusiasts....
- Likes 1
-
Following another extended break, I've installed the passenger front side shock. Also, I've turned my attention to the driver's side rear brake system....
- Likes 1
Leave a comment:
-
A few updates to report. I've purchased a Comp Cams he268 cam/lifter kit for the low compression 350, after finding a worn lobe on the cam I planned to...
- Likes 1
Leave a comment:
-
I'll add that to the 'To-Do List' . Thanks for the info, Limey SE ....
Leave a comment:
-
Replaced the rear driver's side air shock with the KYB shock and painted the brake drum. While I was painting the drum, I cleaned and painted driveshaft...Last edited by Cammin; November 16, 2022, 09:35 AM.
- Likes 1
Leave a comment:
-
Look who's back in the game! After more stops and starts, I've replaced the rear passenger air shock with a new KYB shock, along with painting the brake...Last edited by Cammin; November 8, 2022, 07:34 AM.
- Likes 4
Leave a comment:
-
-
Finally have an update worth sharing. Purchased a 6v-53 Detroit Diesel blower for $100. After a good bit of searching, I found that Joe Blow Speed Shop...Last edited by Cammin; April 8, 2021, 12:53 PM.
Leave a comment:
-
Good news. I picked up a low mileage 350 ci. GM crate engine from a local rebuilder for $800. Whenever I get time, I'll swap the short block...Last edited by Cammin; November 10, 2022, 06:26 PM.
Leave a comment:
-
After a few bumps in rhe road, this project is back on track. Up next, the engine is coming out. We'll see what happens next.
I picked...1 PhotoLast edited by Cammin; July 11, 2020, 05:04 PM.
- Likes 3
Leave a comment:
-
After years of sitting outside with no cover, it had amassed an impressive buildup of crud over the entire body. Now it feels smooth to the touch again...
Leave a comment:
-
Long time coming, but finally ready to pull the engine when time allows. Gave it a Comet and Scotch Brite bath yesterday. I'll update when the engine...1 Photo
Leave a comment:
-
Quick update: I've pulled the driveshaft, which I plan to paint and replace the u-joints. I'll be pulling the engine this winter for the rebuild and I...
Leave a comment:
-
Much like life, this project has taken a few turns lately.
The engine I was planning to use is in approximately the same condition as mine,...
Leave a comment:
-
Unfortunately, I don't have vacation days or sick days available. The day for extraction is coming soon though........
Leave a comment:
-
Quick update: I've been offered a free, running 350 (fully dressed) if I pull it. So, I'm planning to make the short drive to pick it up within the next...
Leave a comment:
-
Finally got black lugs nuts that fit the wheels (thanks for info) and it is now sitting on the ground with 4 tires that hold air, for the first time in...2 Photos
Leave a comment:
-
PIcked up an iron manifold (3965577) for $10 at a yard sale. What recomendations do you have for removing or covering rust in the intake ports? As always,...2 Photos
Leave a comment:
-
Thanks for the information. Next question for you folks... I pulled the cylinder heads off and found that the driver's side cylinder head gasket was leaking...Last edited by Cammin; May 25, 2016, 05:25 PM.
Leave a comment:
-
It's been a few days since my last update, so here goes:
I've got a cam and lifter set for the Camino now, after helping a friend install...1 Photo
Leave a comment:
Leave a comment: