Well i did it now

[milner351]

Sorry - I don't have any wheels that wide to lend you for a fit up. Have you decided on a cam yet? Did you call cam research?

[quick 52]

Sorry - I don't have any wheels that wide to lend you for a fit up. Have you decided on a cam yet? Did you call cam research?

pretty much going to stay with what is in there it a clay smith SFT... hope to step up next year with a new engine got the go ahead from the wife so think a 521 ci sounds good or maybe just more spray... hope this work is worth the time if so think 10.50 this summer

[DanStokes]

A bit off topic (how normal on here) but is Leonard Refining still in business?

For you non-Michigan folks, Leonard had a small refinery and a string of gas stations around MI (maybe in adjacent states - not sure on that) for many years, bearing the "Leonard" name. They often sponsored the weather on one of the Detroit TV stations. Just wondering if they're still alive.

Dan

[Dave D]

Dale,
I'm not sure how well those look from the photos. Do you have them on 10" wide wheels?
When you're done those 29.5's will 60 better than the smaller slicks and take all the spray that you can throw at em.

Dave

[quick 52]

Dale,
I'm not sure how well those look from the photos. Do you have them on 10" wide wheels?
When you're done those 29.5's will 60 better than the smaller slicks and take all the spray that you can throw at em.

Dave

Dave i do have 10" rims but do have room for larger 12" 14" we'll see for now its just get it ready for paint so the summer is coming

[quick 52]

A bit off topic (how normal on here) but is Leonard Refining still in business?

For you non-Michigan folks, Leonard had a small refinery and a string of gas stations around MI (maybe in adjacent states - not sure on that) for many years, bearing the "Leonard" name. They often sponsored the weather on one of the Detroit TV stations. Just wondering if they're still alive.

Dan

have seen the leonard gas station growing up didnt known it was from leonard mich. .. ive only lived out here around 8 year's. there a natural gas plant still in leonard but is shut down south of town on rochester road.

[quick 52]

well made it out to the shop today and fitted the other side of the floor around the tub and played with so aluminum 1x1/4 bar to see how hard it is to bend around the tubs look like i can get it to work... hope to work on welding the tubs in fri. with easter coming will be with the grandkids eating hamb all weekend... sat. going to trackwith my sons mustang trying to get a 11.60s out of it with the cool weather have been 11.86, 11.88, 11.91. with DR but got new slicks so will see. 2012 GT 6speed

[quick 52]

here some pic.

[1956NY150]

Your're Screwed NOW that I KNOW what YOUR Doing!

[quick 52]

Your're Screwed NOW that I KNOW what YOUR Doing!

I was screwed the minute i cut the bed what a fool will do

[quick 52]

went out to the shop to clean up that aluminum is a mess... notice that the towel i had covering a trans with the pump out fail off.. so far for not taking time now i need to tear the trans back down for a cleaning should of finish the trans a couple months ago

[MattDuCharme]

Sorry to hijack.....

We had them on 14s or 15s and they where huge! On a 10 they would be round on the edges pulling them up I would think

315 on a 14 wide rim? I cant seem to find any pics of that setup - i would think that would look funny wouldnt it?

[quick 52]

got out to the shop today but a flange on the bottom of the tub on the pass. side... then welded it in and ground down the weld on the bed side still need to grind the outside hope flange the other tomorrow and post some pic

[TC]

Sorry to hijack.....



315 on a 14 wide rim? I cant seem to find any pics of that setup - i would think that would look funny wouldnt it?

Here you go Jeff was a trend setter back in the day.....



Or maybe it looked more like these.....

[cstmwgn]

There you go Dale - those would look AWESOME on your F1!