Category Archive: ENGINES, Videos
Ground Testing: Watch As These 427 Ford Engines Are Ground-Tested After Being Removed From A Chris Craft Boat!
Sep 26, 2016Bryan McTaggart5
When a car is wrecked, salvagers go for what didn’t get hurt in the collision. Same thing happens with boats…or, at least, one boat in particular. This 42 foot long Chris Craft...
After Getting Bashed In The Comments For The Header Bash Episode, Engine Masters Takes A Second Swing At The Dented Headers Myth!
Aug 09, 2016Bryan McTaggart5
It just might have been the only time David Freiburger will ever admit to beating up Hookers, but in an early episode of Engine Masters, they bolted up a set of Hooker Headers to a BluePrint 400ci...
Take Your Sides, It’s The Battle Of The 408 Cubic Inch Small Block Strokers! Ford Versus Mopar!
Jul 12, 2016Bryan McTaggart4
There’s nothing quite like a head-to-head comparison between two manufacturers to stir up the masses, is there? The fastest way to get sure-fire results in the comments section of a video that...
Hot Rod Garage Jams A Supercharged Mill Into The Crusher Camaro – 700+ Wheel Horsepower!
Jul 02, 2016Bryan McTaggartComments Off on Hot Rod Garage Jams A Supercharged Mill Into The Crusher Camaro – 700+ Wheel Horsepower!
It only seems like yesterday that the Crusher Camaro, that other bright yellow GM product that has been in the magazines forever, was getting a new engine courtesy of Mast Motorsports. In fact, it...
Hydraulic Roller Or Solid Lifter…Which Cam Works Out Better? Engine Masters Flogs The Dyno To Get The Answer!
Jun 14, 2016Bryan McTaggart1
This is a fun comparison: which camshaft will perform better in a Chevrolet 454 that is wicked up to hang easily in the 600 horsepower range and provide the power you crave? On one hand, you have a...
Add Cylinders And Go: Check Out This LS-Based V-12 Engine On The Dyno!
Jun 13, 2016Bryan McTaggart6
In 1966 the last General Motors-built twelve cylinder engine, the famous 702ci “Twin Six”. Based upon the GMC V6 family of engines, the Twin Six utilized a good amount of parts from the...
Video: Watch The Biggest And Baddest Ford Production V8 Of All Time Shoot Fire And Sound Pissed! 1100ci!
Jun 05, 2016Brian Lohnes2
That’s right, the biggest and baddest ass production Ford built V8 in the company’s long history was an 1100ci, all alumimum, dual overhead cam, 32-valve piece that made over 1,000 lb/ft...
Which Loses More Power: A Three-Inch Exhaust Or A 2.5 Inch Exhaust? Engine Masters Tests Out The Backpressure Theory On A Chevrolet 454!
May 17, 2016Bryan McTaggart14
Here’s a fun question that you can use to fire up just about any message board: what does a high-horsepower engine like better: a 3″ exhaust to breath better with, or a 2.5″ exhaust...
Morning Symphony: The Bugatti Chiron In All Of It’s 1,479 Horsepower Glory
May 08, 2016Bryan McTaggart2
Let’s get the problems out of the way now: it redefines “expensive automobile”, will become either a testbed for companies or playthings for the stupidly rich, and out of the...
Which Supercharger Is Best? Engine Masters Takes A Look At Two Budget-Minded Boost Possibilities On The Ford 363ci Yanked Out Of The Raunchero!
Apr 19, 2016Bryan McTaggart3
Boost…it is addictive, it is fun, and normally, it’s a bit expensive to do. Superchargers can provide enough pressurized air to make the drive a lot of fun, and blower whine is always so...
Engine Teardown: Watch As This Porsche 930 Turbo Flat-Six Gets Taken Down To The Bare Block!
Apr 11, 2016Bryan McTaggartComments Off on Engine Teardown: Watch As This Porsche 930 Turbo Flat-Six Gets Taken Down To The Bare Block!
Spring is a little late to be tearing into a project engine, but better late than never. The sooner the engine is torn down, the sooner it can be built back up to be even better than it was before....
Hot Rod Garage Makes A 512 Cubic Inch Stroker Out Of A Throwaway Block And Jams It Into This Awesome Fury Station Wagon!
Apr 10, 2016Bryan McTaggart7
Laying around in the Hot Rod Garage arena was one particular 400 cubic inch Mopar big-block. And it had a sad tale: it was in the truck that Freiburger originally bought to use as an engine donor for...
Engine Masters Tests CNC-Ported Heads Against Vortec Heads On A 383 Chevy To See If The Performance Gain Is Worth The Cost!
Jan 27, 2016Bryan McTaggart7
Ever been bench racing with some buddies and come up with a build plan? Does it usually sound like, “I’m gonna build a (insert engine here) and I’m gonna run this intake, these...
Can You Make Hellcat Power From A Chrysler 5.7? Engine Masters Slaps A Paxton Blower On One To Find Out!
Jan 20, 2016Bryan McTaggart3
When it debuted in the early 2000s, Chrysler’s 5.7L Hemi was a stomper. Rated at 345 horsepower in trucks and 340 horsepower in the cars early on, it was a good volley into the horsepower wars....





