Category Archive: BangShift XL, CRASH & BURN, FUNNY STUFF, Videos, XL Videos
Video: A Mustang, A Firebird, and An RV Walk Into A Tuff Truck Competition And All Race!
Ok, well they did not walk into the SAME Tuff Truck competition but the all did race and the videos below are total proof of that face. You are going to see a Fox-body Mustang get hammered so hard it...
This Rad Vintage GMC Prerunner Is An Epic Use Of Suspension, Wrapped In Attitude, And Powered By A Blown Small Block.
The 1941-1947 Chevrolet and “GMC” trucks were often referred to as the Art Deco trucks, and I doubt anyone who helped coin the phrase ever thought one would end up looking like this. I...
Unimog vs The World! Can Anything Else At King Of The Hammers Keep Up With This Thing?
We’ve been following a Unimog Expedition vehicle build on here recently, and I have repeatedly said how much I dig them. They are amazingly utilitarian but also incredibly trick in how they...
Hauling Post: Chip Foose Takes His Swing A Designing The Ultimate Hot Rodded Mail Truck
The Grumman LLV is a staple vehicle on American roads. The little mail trucks that trundle around your town or city have a reputation of being ugly, slow, and completely uninspired but they are also...
You Can’t Start The Car Hauler Rebuild Until You First Finish The Demo: A Complete Car Trailer Remodel Starts Right Here
The Reeves are at it again, doing something I have thought about for a few years. I see all these guys and gals at the races with big fancy trailers and have zero clue how they all afford them. I...
Morris Minors Are Cool, But This One Is Lifted, 4-Wheel Drive, CARBON FIBER And A Serious Bad Ass Compared To Stock
My dad was 5 or something when my Grandpa Reynolds let him drive the car for the firs time. It was a Morris Minor, and it didn’t last long. At the bottom of their street, unable to reach the...
When Rick Pewe Describes Says “That’s An Epically Cool Thing Of Beauty” It’s Got To Be Good
Rick Pewe is the most hard core Jeep guy I know. As far as he’s concerned, every Jeep that matters came with flat fenders, or something like that and I’m not one to argue with him....
The Unimog Expedition Vehicle Build Continues! It Has To Come Apart Before It Can Go Back Together. But First, A Little Camping Trip As Is.
When we first started following this project, I told you that a Unimog has always been on my list of off-road wants. They are super cool, have amazingly well thought out technology, and yet are as...
Ian Johnson’s Willys Wagon Is Going To Be One Awesome Ride. Check Out The Progress Right Here.
We started sharing the videos from Ian Johnson’s Willys Wagon build last week because its a project we really like the direction on. This thing will be a family wheeling machine, but is being...
Tim Strange Installs The New QA1 Coil Over Conversion On The Front Of His OBS Chevy Truck.
Yesterday we shared the install video where Tim Strange of Strange Motion, along with friend Ryan Harris, installed the complete torque arm coil over suspension system on the back of Tim’s shop...
Learn How To Bead Roll With Finnegan! He Brings Jamey Jordan In To Give Him A Personal How To.
Bead rolling is something I have only done a couple of times in my life, and never for more than a couple ribs to strengthen a floppy panel. If I owned a bead roller, that might be different, but...
Tim Strange At Strange Motion Installs QA1’s OBS 99-98 Chevy Truck Coil Over Rear Suspension
OBS trucks are all the rage right now, which comes as no surprise to those of us that have been OBS fans since back in the day. Tim Strange is one of the OG OBS guys, so it should come as no surprise...
Another Kibbetech Tube Chassis Race Truck Update, Plus Project Updates And New Parts.
As we said in the last installment, Kibbetech makes some cool parts and pieces and builds some awesome off-road rigs. If you are into desert racing and pre-runners then you know Kibbetech. They are a...
The Fab Rats Cut In Half Jeep Is Going Back Together: Brakes And Sheetmetal. Will It Work When Done?
Last month we showed you the Fab Rats Jeep project that had them cutting it in half and then getting rid of most of what was connected to the back half. So far they have extended the frame, gusseted...