Karl Fisher From Make It Kustom Shows Us How To Make An EASY, FREE, DIY SHRINKER TOOL! HOW-TO Make CURVED FLANGES on SHEET METAL!
In this episode, Karl makes a DIY shrinker from scrap he had laying around. And I know I could absolutely do the same thing with junk I have sitting around. I’m sure you can too. And if you...
This Bad Ass Jeep Is Showing Supercars What The Back Of A Cherokee Looks Like On The Way To Gapplebees
I’m a huge fan of things that haul ass, and especially things that haul ass but don’t look like they should haul ass. I mean sure this Jeep Cherokee has wheels and tires on it, and a...
A $1,000,000 RV That Isn’t A Toter And Stacker!? Touring a $1 Million SCANIA RV Imported from HOLLAND!
Bruce Wilson is an RV reviewing machine and gets some of the coolest access to stuff that you and I would NEVER get to see otherwise. And while all of us racers are used to seeing stupid fancy...
Watch The Awesome and Pretty Complicated Starting Procedure For A 1958 John Deere 820 – Pony Motor!
If there is a basic rule of life it is that any engine that needs or happily uses another engine to start it is pretty awesome and the big (400+ ci) two cylinder John Deere diesel is nothing but...
An Amazing Tale: The Story Of The Rotodyne, The Vertical Take Off Airliner That Almost Made It (Video)
When we think of failed aeronautical innovations we normally put them in the same category known as, “stuff that could not actually fly.” Well this video and this story will stand as...
Budget Shop Truck: Squarebody Long Bed To Short Bed Conversion – CHEAP REPAIRS. Basic Patch Panel How To With A MIG Welder
This cool low buck shop truck build is turning out really cool and we dig it. If you missed it, the long bed became a short bed, using the stock bed with the smallest of cuts and welds so that the...
Remember Bigfoot and USA-1 Racing Down Lanes of Crushed Cars At Gateway Motorsports Park In 1983? Let This Video Remind You
This video is absolutely awesome on every single level and we have to thank Chuy Nava for thinking of us and tipping us off to its existence. You are going to jump back in time to 1983 and to the...
Twin Turbo S10 RIPS On The Street! Blasting SUB-ZERO down a Back Road For Science. See This Thing At PRI In The Melling Booth!
The SUB-ZERO S10 is back and ready to rock. But instead of just shining it up for the PRI Show and leaving it alone, they are doing some upgrades and then doing testing. Again, nobody would know if...
How to Remove Rust – 6 Easy Ways to Protect Bare Metal With Willomet Motor And Fab’s 1970 Dodge Charger
We’ve all had to deal with rust repair on a project before, but what about the rust that shows up when you start working on something with new metal? I’m talking about two months into...
MOST POWERFUL LS3 INTAKE EVER? SUPER RICHIE DUAL-PLENUM, ADJUSTABLE RUNNER LENGTH AND PLENUM VOLUME
One thing some of his casual fans may not realize is that Richard Holdener has not only done all the testing and tech stories for magazines and websites for decades, but has also done a LOT of...
Demo Derby In Car Video: Watch A Cadillac Take Four Minutes Of Pounding Before It Spits The Bit
Ahhhh, the demolition derby. Long a staple of county and state fair entertainment it is about as pure a concept as you can get. Bash your brains out and the last man or woman running wins. Being the...
What’s Worse Than Turning Your Pulling Tractor Over? Turning It Over And Blowing Up All The Engines
We have showed you plenty of pulling mishaps over the years but this one has a special class that it will end up in. Why? Not because of the rather gentle roll but because of the fact that after the...
Let’s Go WWII Wheelin’: This 1940s US Army Training Video Teaches Drivers How To Handle Tough Terrain
This is some awesome WWII history right here. You are about to watch a training film shown to WWII Motor Pool drivers to aid in their training with regard to how best to cover and traverse difficult...
Building our first customers roll cage for his C10: what we charged & how much profit we made! The Right Tools And Methods Are Key!
Video Description: In this video Matt and Kevin show you how to build a cage to fit a C10 Chevy truck. We start with a custom fitting while the customer is in the C10 truck. To do this we used our...
