Category Archive: 1320 Spotlight, 1320 Tech Story, 1320 Videos, OTHER, TECH, Tech Stories, Videos
Video Of Rob Wendland Front Halfing Larry Dixon’s Top Fuel Dragster: Sounds Simple, But It All Has To Be Perfect!
It isn’t uncommon for Top Fuel and Top Alcohol cars to get front halfed after a certain number of runs, a crash, big wheelstands, or what have you. The same could be said for a Funny Car...
Here Are The Top 10 Shootout Runs From The Goodwood Festival Of Speed
Goodwood’s Shootout happened yesterday, but if you missed any of it then here are the 10 Quickest Runs, all in one video. This is an event we would love to go to, as it is a must attend...
What Should You Paint Your Roll Bar Or Roll Cage With? Rustoleum, Hammertone, And Steel-It Tested
There is nothing worse than finishing a car with a roll bar or roll cage in it and then not being able to paint the cage well. In all honesty, a tube chassis car is usually much easier because you...
Grinding Inside Corner Welds Isn’t Hard, But It Is Easy To Mess Up!q
Grinding seems like a pretty simple thing, especially when it comes to prepping a joint for welding or grinding a weld smooth. With that said, I’ve seen jillions of people do it wrong and the...
Coeburn Cash Days: Virginia’s Lonesome Pine Raceway Hasn’t Had A Car Down It In Nearly 50 Years. This Is No Prep!
There’s no prep, where they take a dragstrip and usually scrape some of the track and then never prep it again for the rest of the weekend, and then there is this. This dragstrip hasn’t...
New Products: Terminator X High Impedance-Fuel Injectors in Multiple Flow Rates
More power often means the need for bigger fuel injectors, and so does an engine build that isn’t starting with stock components. So why buy stock stuff and try to work with it when there are...
How To Pin The Crankshaft On An LS Engine. (NO MORE SLIP = MORE BOOST AND HP) FULL RESULTS
LS engines have a press-fit harmonic balancer, damper, whatever you want to call them, and they are an interference fit that requires a balancer installer to put one on and sometimes a hydraulic...
The Chicken Coupe: Pro-Touring Cadillac Coupe Deville Project Continues! Suspension And Brakes!
We ran the first video on the Chicken Couple project yesterday and told you that more was coming. Well here is video number two. There are going to be a lot more videos and a lot more content coming...
Alex Taylor’s Quest For The Sixes 1955 Chevrolet Project: Driver’s Compartment Fitted And Steering Working!
There is a ton that goes into making something that is going to run 6’s in the quarter mile, even if it is just a pure race car. But if you are going to do that with a street car, with steel...
An Electric Subaru Brat? Okay, This Is An Electric Vehicle Swap We Think Might Be Real Fun!
The idea of taking a gas or diesel-powered car and making it electric intrigues me. I think it would be a fun project and have been thinking about a few different fun cars to do the conversion on. Of...
Check Out This See Through Carburetor Working In Ultra Slow Motion!
So just to be clear, this is NOT a Holley 4-barrel or something. This is a little single barrel carburetor like you would see on a small engine on your minibike or lawn mower. But the way it works is...
Using A Cement Mixer To Clean A Gas Tank: Edd China’s Workshop Diaries Might Be Going Off The Deep End
A cement mixer? Hmmmm. Think about it and it starts to make some sense, especially if you watched the last episode where Edd was trying to get the rust out of the Range Rover gas tank. He put a bunch...
Pro-Touring LS Swapped Cadillac Coupe Deville- Introducing The Chicken Coupe, A Project That Excites Me To No End.
The Chicken Coupe has been a long time coming and is a project that I am behind 100%. After all, good friend Matt Graves is the one behind this craziness and he’s been involved in some...
